Zemin Boyama Sistemleri - ZBS GLOSSY FLOOR TRANSMISSION PRIMER

ZBS GLOSSY FLOOR TRANSMISSION PRIMER

Product Code :

CATEGORY : Floor Painting

Subcategory : ZBS ROAD AND FLOOR COATING


CERAMIC, GRANITE, PALEDIAN, MARBLE, TILE AND GLOSSY AND / or MATTE SURFACES PREPARE THE FLOOR AND A HEALTHY TRANSITION FOR A STRONG ADERENCE (ADHESION) BEFORE APPLICATION.

Acrylic dispersion based, filled, ready to use, thick density, suitable for paint and plaster applications on ceramics, adhesion increasing primer material.

 

usage areas

It is used in all buildings to make the floor suitable for adhesion (adherence) before the application of paint or plaster on surfaces such as Tiles, Ceramics, Paledian, Marble, Granite, Tile etc. It is recommended to be used on vertical surfaces by making the applied surface rough and toothed. It forms nails on the surface. Thus, it provides a suitable adherence environment where plaster and paint or any coating can hold, as well as maximizing the life and strength resistance of the application.

FEATURES ADVANTAGES

It makes the surface rough thanks to its special fillings and aggregates. It provides effective solutions. It is ready to use material. not diluted. It is sliding based and easy to use. It provides high adhesion. It is single component. It reduces water absorption on the surface.

SURFACE PREPARATION

Ambient temperature should be between +20 ⁰C and +35 ⁰C. The surface to be applied must be clean, dry and intact structure. Factors that affect adhesion such as oil, rust, cement on the surface and cannot carry themselves should be removed from the surface or scraped. Oil and petroleum-derived stains should be cleaned using cellulosic thinner. Synthetic thinner should never be used. Application at very high temperatures and very low temperatures should be avoided. Drying time is minimum 2-4 hours.  

APPLICATION

Before using ZBS Ceramic Transition primer, it should be mixed thoroughly until it becomes homogeneous. Thinning should not be done. Mixing should be done with a low speed mixer if possible. ZBS Ceramic Transition primer is applied in one layer with the help of a roller or brush. Since its product has high viscosity (density), it is thick and close to paste. Herewith, the roll can be difficult to move on the ground. Nevertheless, it should be ensured that the product is spread evenly and evenly on the floor and applied evenly and evenly.

APPLICATION TOOLS

Insulation brush, roller,  

SHELF LIFE

It is 2 years from the date of manufacture in dry and dry environments. When not in use, the packages should be closed tightly. 

CONSUMPTION

Approximate consumption for a single coat is 0.40 - 0.65 kg / m². Consumption amounts may vary +/- depending on the application surface.

WARNINGS AND PRECAUTIONS

Tools should be cleaned after application. It is not applied on metal surfaces, chipboard, plywood and wooden surfaces. The application surfaces must be dry. If it is a wet surface or washed before, it must be expected to dry in moisture under the floor. Foreign materials should not be added to it. Our company is not responsible for the application errors that may occur as a result of using the product out of its intended purpose, not complying with the conditions and recommendations stated in the warnings and precautions section.

PACKING

25 kg plastic (Polyethylene) bucket.

ATTENTION OF OUR CONSUMER:

Even if our ZBS Ceramic Transition primer product is used, some Ceramic etc. surfaces may not have long-lasting results. Because, concrete, cement based surfaces, epoxy etc. are used in all brands and serial ceramics. There is no standard or surface that we can be sure of in advance. Due to factors such as the surface details in the patterns and models arising from the differences of the manufacturer, the cooking time of the ceramic in the oven, the lacquer texture on it, some ceramics etc. adherence problems may occur on surfaces. In order not to be affected by this situation, a trial application can be made on a part of the ground, and it can be experienced after the aging process.

PRODUCT INFORMATION

APPEARANCE / COLOR Red colored viscous liquid
GRAIN SIZE 0 - 0.4mm
APPLICATION TEMPERATURE Between + 20⁰ C and + 35⁰ C
CONSUMPTION 0,50 -0,65 kg / m²
DENSITY 1600 ± 100 g / lt

PRODUCT REQUIREMENTS 

E-NEWSLETTER SUBSCRIPTION

E-Newsletter Subscribers Can Instantly aware whether our campaign.